Introduction
Sewerage Charges are recurring charges which are levied on for a pre-defined billing period. Billing The billing period can be is configurable as per the state or ULB requirement. The rate for calculation of sewerage charges can vary widely and can be is dependent upon various parameters. For eg. instance, they can be dependent either upon either plot size slab combined with property usage type or solely dependent upon property usage type. In some cases, sewerage charges can also be levied as some a percentage of water charges.
Data Table
Sr. No. | *Property Usage TypeProperty size slab | *Calculation attribute | Slab value from (units) | Property size slab Slab value to (units) | *Charges | |
---|---|---|---|---|---|---|
1 | Residential | Property Size | 1 | 150 | Rs 5/ unit | |
2 | Residential | Percentage of water charges (%) | NA | NA | 10 % | |
3 | Commercial | Flat fee (in Rs) | *Rate NA | |||
1 | Residential | 0 | 150 | 30 | 200 | 5 |
2 | Commercial | 150 | 300 | 40 | 500 | 10 |
NA | Rs 300 |
Note: The above table contains sample data for sewerage rates.
Procedure
Data Definition
Sr. No. | Column Name | Data Type | Data Size | Mandatory | Description | |||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Property usage type | ReferenceText | 64 | Yes | Specifies the Refer to property usage type | |||||||
2 | Calculation Attribute | Text | 64 | Yes | Depending on the case, calculation attribute can be Property Size value, percentage of water charges or a flat amount. | |||||||
3 | Slab (Property size value) | Decimal | (10,2) | Yes | Conditional Mandatorymandatory. From and to value for property size | 3 | Flat fee | Decimal | Conditional Mandatory | Flat sewerage charges collected based on property usage type | ||
4 | Percentage of water chargesCharges | Decimal | Conditional Mandatory | Percent value | 5 | Rate | Decimal |
| Yes | Consumption (3,2) | Yes | Depending on the calculation attribute charges can be consumption charges per unit corresponding to the usage type or a percentage or a flat amount. |
Steps to fill
thisdata
Download the data template attached to this page.
Get a good understanding of all the headers in Refer to the ‘Data Definition’ section of this document to learn more about the template sheet, their data type, size, and definitions by referring to the ‘Data Definition’ section of this document.In case of any doubt, please .
Please reach out to the person who has shared this template with you to discuss and clear your doubts.
Get information about charges levied for sewerage connection as a part of bill
Get slab range and rate information for corresponding property usage type if applicable
Get percentage value for calculating sewerage charges based on water charges
Property usage type collected from State/ULB should be mapped with DIGIT property moduleSelect the relevant Property Usage Type from the available drop-down list.
Enter the From and To value for property size to specify the range applicable for the selected property.
Enter the Flat Fee applicable for the selected property and Slab.
Enter the applicable Percentage of Water Charges value. The sewerage charges will be calculated as a percentage of the water charges.
Enter the corresponding consumption Rate per unit.
Verify the data once again by going through the checklist and making sure that each and every point mentioned in the checklist is covered.
Checklist
The checklist is contains a set of activities to be performed one once the data is filled into a template to ensure data type, size, and format of data is as per the expectationentry requirements are met. These activities have been divided into 2 groups as given below.
Common Checklist
This checklist covers all the activities which are common across the entities.
Sr. No. | Checklist Parameter | Example |
---|---|---|
1 | Make sure that each and every point in this reference list has been taken care of. |
Entity Specific Checklist
This checklist covers the activities which are specific to the entity.
Sr. No.
Checklist Parameter
Example
1
Property usage type should be mapped to ontology present in property module
‘Domestic’ in W&S = ‘Residential’ in PT
2
Slab (Property size value) should be a decimal value
120 : [Allowed]
120 sq. mt. : [Not allowed]Separate Entity Specific Checklist is not required for this module data.